Hakko 927 E.s.d. Manual
Hakko Soldering Station Manual. This is a partial text extraction from the pdf, to download the pdf, click the Manual tab. If you want to search this text, hold. Hakko 927 E S D Manual Lymphatic Drainage Look up local research clinics in your phone book and ask (a) if they have any studies openly recruiting healthy. September 2 1. HEMIST AND DRUGGIST. SEPTEMBER 2 1. Always keep an. LTD., OLDBURY, WARLEY, Worcestershire. September 2, 1. THE CHEMIST AND DRUGGIST.
. HAK(O HANKTATIOON Please read this instruction manual thoroughly before operating HAKKO 9P+6. Specification. Station Power Consumption Output Voltage AC24V Temperature 200480°C/392-896°F Temperature Control Control accuracy of setting at idling temperature.:/-0.5°C (+0.9°F) 125(W) x 120(H) x 200(D) mm Outer Dimensions (without Cord & Holder Part) 4.9(W) x 4.7(H) x 8.1(D) in. Approx 1.5 kg (3.3 lb) Weight (without Cord &.
Accessories $ Holder Part (consists of: Iron receptacle, Iron Holder Body, Holder Mounting Base, Thumb Screw). Cleaning Sponge.
O E S D Embroidery Designs
Tip& Sponge Tray Part Name Handle Cover Temperature Control Knob Handle L.E,D. Heater Lamp Nipple Power Switch Holder Part Holder Body Thumb Screw Cord Asse'y. Precautions Ceramic Heating Element cannot stand excessive force.
Never strike Soldering Iron against work-bench or solid surface. Make sure the Nut securing the Tip Enclosure is properly tightened. Use exclusive Tips for 900 only.
Operate in lower tip temperature. Exceptionally high thermal recovery allows. Replacement. Caution Temp, compansion with the standard tip. (At 480°C, 896°F) 1 ) Use exclusive tips for HAKKO 900 only. 900M-T-1,6D.= 2 ) The set temperature should be adjusted M-T-2.4O.,.o%., according to the tip configuration. If required, adjust the temperature.
Los Power Ranger E S D
Trouble Shooting Guide Problem: Turn the power switch on, but Tip does not heat up or over heating. Condition: The power lamp doesn't light up. CheckPoint: Is the fuse blown? Condition: The fuse is blown. CheckPoints: 1. to check the breakage of Heating Element and Cord Asse'y.
Disconnect the Connecting Plug and measure the resistance value between pins of Connecting Plug as follows Between pin 4 & pin 5 2.5-3.5 ohm (Heating Element) (Normal) Between pin 1 & pin 2 4358 (Sensor) (Normal). Recalibrating of Iron Temperature After replacing the Heating Element or replacing the tip, recalibrate the temperature of the Soldering Iron. 1 ) Connect the Plug of Soldering Iron to the Station and lock it.
2 ) Set Temperature Control Dial at 400'C (752°F). 3 ) Turn the Power Switch.
g Heating Element D-Sleeve 'J' O Nut O Tip Enclosure O Tip O Nipple Grounding Spring Heating Element Glass Tube Heating Element Lead (Red) Sensor Lead (Blue) Terminal Board Cord Asse'y Handle 1 ) Turn the Nut O counterclockwise and remove the Tip Enclosure. Replacement Parts Name/Specifications 900M-H Heating Element for 900M Ceramic 24V 50W B1784 Nut for 900M B1786 Tip Enclosure for 900M 900M-044 Nipple for 900M 900M-044S Nipple for 900M (ESD Type) 900M-036 Grounding Spring for 900M 900L-H Heating Element for 900L, Ceramic 24V 50W B1794 Nut for 900L B1787.
CORPOR ION HEAD OFFICE HONG KONG: HAKKO DEVELOPMENT CO., LTD. 4-5 SHIOKUSA 2-CHONE, NANIWAKI OSAKA, 556 JAPAN ROOM 804, EASTERN HARBOUR CENTRE, 28 HOI CHAK STREET, QUARRY SAY, HONG KONG TEL: (06) 561-3225 FAX: (06) 561-8466 TEL: 2811-5588 FAX: 2590-0217 TLX: HAKKOOSA J65274 PHILIPPINES.